LBS(PGS) pole mounted load break switch is used for breaking rated voltage 12/24/36kV,rated current 630A,1250A,50/60Hz power distribution system,closing load current and over load current of power system,it could separate automatically track sections of power distribution which faults occur.The switch is matched with electronic controller which is with the latest technology. The switch has manual,motor,remote operation modes.The electronic controller would be installed inside the stainless steel box, so i could be used in various climate conditions.Besides that,the wire/wireless modem installed inside control box could achieve remote monitoring and controlling.It’s easy and convenient for instllation the switch on pole,and that could reduce the execution cost. Product Advantage 1.SF6 gas-insulated:SF6 gas is a kind of nontoxic,nonflammable and electrical insulating gas.It has the excellent characteristic of arc extinction. 2.Drivepipe with large diversity:In addition to standard ceramic bushing,we can also provide a variety of programs,including rubber insulators in an epoxy bushing device. 3. Visible open /closed status:It is easy to see the main contact position indicator which is color-coded just standing on the ground (Green-off;red-closed).The indicator is directly connected with the main contacts of the drive shaft assembly to ensure accurate display of contact states. 4. Quick operation:Operating mechanism with spring energy to ensure a quick closing and opening operation (less than 100 miliseconds). 5.Can realize remote control:it is equipped with electronic controler,fit for in situ operation as well as FTU interface console operation. 6. Rugged switch:The switch is made of proven durable,corrosion-resistant materials (special used in warships 304L stainless steel plate)which ensures that there is a very long service life(30 years),and can be implement a series of operations.It has the ideal characteristics as a column equipment. 7.Standard:Each switch before leaving the factory has been flled with SF gas,sealed,and test according to IEC60265-1(1988), GB40.504-1990 standard. Technical Parameters

No.	Name		Unit	PGS-12	PGS-24	PGS-36
1	Rated voltage		kV	12	24	36
2	Rated current		A	630/1250	630/1250	630/1250
3	Rated frequency		Hz	50/60	50/60	50/60
4	Rated short-term withstand current		kA	20	20	20
5	Rated Active load breaking current		A	630/1250	630/1250	630/1250
6	Number of disconnections		Times	400	400	400
7	Short time closing current(peak)		kAp	50	50	50
8	Number of short-term closing current tests		Times	5	5	5
9	Cable charging breaking current		A	25	25	25
10	Line charging interruption current		A	1.5	1.5	2
11	Rated closed-loop breaking current		A	630/1250 22	630/1250 22	630/1250 22
12	1min power frequency withstand voltage ofthe main circuit	Interphase and ground (wet test)	kV	45	50	60
		Interphase and ground (dry test)		50	60	70
		Fracture surface (dry test)		50	60	80
13	Rated lightning impulse withstand voltage	Interphase and ground	kV	85	150	185
		Fracture surface		95	150	215
14	Internal arc test		kA	20/0.1	20/0.1	20/0.1
15	Arc extinguishing medium			SF₆gas	SF₆gas	SF₆gas
16	Insulation medium			SF₆gas	SF₆gas	SF₆gas
17	Creepage distance (ceramic)		mm	550	840	1055
18	Creepage distance(silicone)		mm	615	900	1250
19	Protection level			IP54	IP54	IP54
20	Closing/opening time		S	<0.7	<0.7	<0.7
21	Mechanical operations (Guaranteed)		Times	10000	10000	10000
22	Operating temperature(Manual type)		℃	-25(40)~+70	-25(40)~+70	-25(40)~+70
23	Nominal pressure(kgf/cm G,at 20℃)			0.7	1.0	1.0
24	Bursting pressure (kgf/cm G)			4~6	4~6	4~6
25	Minimum gas pressure(kgf/cm G)			0.05	0	0
26	Leakage rate (cc/sec)			1.1×10-	1.1×10-	1.1×10-7

USAGE: ENVIRONMENTAL CONDITION 1. Air temperature:max+50℃,min -40℃; 2.Relative humidity:110%; 3. Altitude:≤3000m; 4. Wind pressure not exceeding:700pa(equivalent to wind speed of 34m/s); 5. Earthquake intensity:8 levels; 6. Installation site:No fire or explosion hazards,no chemical corrosion,and frequent severe vibration; 7. Pollution level:Class III,Class IV. Outline and Dimension

Dimension (mm)			Installation dimension(mm) Length×Width	Packing size (mm) Length×Width×High	Creep distance of bushing (mm)
A	B	C
12kV	225	435	500	500×125(290)	1100×900×700	556
24kV	300	435	500	500×125(290)	1300×1100×700	840
35kV	350	435	500	700×125(290)	1400×1200×700	1250

Model and meaning Ordering Notice 1. Please determine the product model,name,quantity,ratedcurrent,type of operating power supply,operating voltage,etc.as needed 2. According to user requirements,we can provide: a.Terminal or cableoutput; b.Ceramic sleeves and organic insulator sleeves; c.Special fixtures for busbar connection; d.Suspended installation bracket.